-
Out of stockPolished Chrome Shock Crown Nut - Short Type. 17mm hex x 10mm 1.25pitch x 16mm Long. Fits: All Footrest mount bars 70-84 + Fender mount thru point on 76-78's. Part #49-0703 $2.25 Ea.
-
Out of stockChrome Shock Crown Nut - Deep Type. 17mm hex x 10mm x 1.25 pitch x 21mm Long. Fits: Shock absorber upper studs on 74-84 650's. Part #49-0715 $2.25 Ea.
-
Out of stock
Ring Wrench to Adjust Shock Preload. Fits: Our 06-3601/06-3607/06-3608/06-3621/06-3627/06-3641 & 06-3647 shock sets and many other aftermarket shocks. Part #35-5033 $2.90 Ea. -
Out of stockFork Seal Spring Clips (Pk./2) - These clips fit into the groove above the fork seals in the lower fork legs. Fits: All 1977-84 650's ( 35mm. forks ) Part #27-1063 $3.69/Pk./2
-
Out of stockFork Seal Washers Pk/2. Fit on top of Fork Seals and below the spring clips in the lower fork legs. Fits: All 1977-84 650's ( 35mm. Forks ) Part #27-1062 $3.69/Pk./2
-
Out of stockCap (Fork Tube Top Cap/Rubber Plug) - Pk/2 - Original type as used on 1974-76 TX/XS650's + 27-4003 Part #27-1092 $4.20 Pk.2
-
Out of stockCap (Fork Tube Top Cap/Rubber Plug) - Pk/2 - Original type as used on 1977-84 XS650's. Part #27-1091 $5.50/Pk./2
-
Out of stockReplacement Shaft Needle Bearing for #28-1011 Conversion Kit. Part #28-1020 $7.95 Ea.
-
Out of stockFork Seal Set - 34 x 46 x 10.5 - Made In Japan by OEM Supplier. Fits: 1970-76 TX/XS 650's (34mm. fork Tubes) Part #27-1016 $8.95/Set
-
Out of stockFork Seal Set - 35 x 48 x 10.5/11 - Made In Japan by OEM supplier. Fits: 1977-84 XS 650's (35mm. Fork Tubes). Part #27-1007 $8.95/Set
-
Out of stockRing Wrench to Tighten Steering Head Cogged Nuts. Also fits preload adjuster on some stock Yamaha Shocks. Fits: 60 and 65mm. Part #35-3005 $9.50 Ea.
-
Replacement Shock Rubbers, Spacers, and Washer Set. For shocks with Eye Type Mounting Points. Fits: Our shock sets #06-3601, 06-3607, 06-3608, 06-3621, 06-3627, 06-3641, 06-3647 and some other brands. Each Set Contains all items shown (in quantities shown). for one shock absorber. Part #06-3734 $9.90/Set as shown ( for one shock )
-
Out of stockSwingarm Grease Seal Set - Holds grease into bushings & shaft area of swing arm. Helps seal out water & dirt. If your bike has originals they should be replaced! (20+ years). Made in Japan. Fits: All 650's 1970-84 Part #28-1025 $11.85/Set/2
-
Out of stockFork Seal Dust Covers (Pk/2) Fits: 1977-84 XS650D-K ( 35mm. fork tubes ) Part #27-1065 $16.95/Pk./2
-
Out of stockFork Seal Dust Covers (Pk/2) Fits: 1971-76 XS/TX650's ( 34mm. fork tubes ). Part #27-1066 $16.95/Pk./2
-
Out of stockSwingarm Pivot Bolt (Shaft) - Bolt with full size thread ( replaces undercut original ). Fits: XS650's 1974-84. Check your original for cracks at the threads. Part #27-1067 $21.95 Ea.
-
Fork Gaitors (Set/2) for 1970 XS1 650 but adaptable to All 1971-84 models. (Remove stock dust covers). Give your 650 that "British" look. Provides great fork protection. 1970 models had a lip piece on the lower triple tree on whicht o clamp the boot, for later models simply insert a piece of split rubber rad hose inside and clamp the upper part of the boot to the fork tube. We suggest a breathing hole be punched on a lower pleat also (face to rear) to allow venting of air. Part #27-1089 $22.95/Set/2
-
Sale!Fork Tube Caps - Set/2 - Stock Steel OEM type - Flat bottom no preload adjuster. OEM Ref.# 1T3-23111-50-00 Caps Fit: 35mm. fork tubes on XS650D (1977) and also fit to all 1978-84 fork tubes Recommended type for 77-84 models using our 27-1088 progressive type fork springs and/or our fork damper valves #27-1086. Note: Use Fork Cap Tool (17mm Hex) #35-1081 to remove or install. Caution! Fine thread, use care when installing. Part #27-4003 $29.95/Set/2
-
Out of stockFork Tube Caps - Set/2 - Stock Aluminum OEM type. Replaces OEM # 341-23111-50/51 Caps Fit: 34mm. fork tubes on TX650A (1974) & XS650B/C (1975-76) Note: Use Fork Cap Tool (17mm. Hex) #35-1081 to remove or install. Caution! Fine thread, use care when installing. Part #27-4002 $29.95/Set/2
-
2F0 type Fork Tube Caps - Set/2 - Stock Aluminum type but with No preload adjuster. Caps Fit: 35mm fork tubes on XS650's 1977-84. Replaces troublesome adjustable US model Cap used on 1978-84 650's Note: Adjustable caps were never used on 650's outside of North America. 22mm Hex top Caution! Fine thread, use care when installing. Part #27-4004 $29.95 /Set/2
-
Sale!Performance Progressive wound Front Fork Spring Set. Springs improve handling while retaining OEM geometry. Stops front end droop and diving during braking while improving cornering stability. Progressive design combats bottoming in harsh conditions by increasing resistance as spring compresses. 24mm. Dia. x 484mm. long. 25/35 Lb./in rate Fits: 35mm. stock forks on XS650 (1977-84) Part #27-1088 $45.95/Set/2
-
Sale!Front Fork Damper Valves (Pk./2) Tuneable Valves are installed on top of the front fork dampening rods and below the fork springs. The adjustable Damper Valve make rod style fork dampers perform like modern cartridge style forks. Fits: 35mm. forks on 1978-84 XS650's. The Best suspension upgrade modification for the XS650 Note: Damper rod drilling required. Photo install instructions included. Part #27-1086 $42.95/Pk./2
-
Sale!Steering Head Bearing Kit - Kit replaces factory loose ball bearings & races. Tapered Roller bearings have 10 times the contact area and less flex. Drop in replacement for factory original type. Japanese made Superior Quality. Fits: 1970-84 XS/TX 650's. Part #28-2009 $38.95 Set
-
Sale!
Performance Progressive wound Front Fork Spring Set. Springs Improve handling while retaining OEM geometry. Stops front end droop and diving during braking while improving cornering stability. Progressive design combats bottoming in harsh conditions by increasing resistance as spring compresses. 23mm. Dia. x 495mm. long. 30/40 Lb. /in rate. Fits: 34mm. stock forks on TX650A (1974) and XS650B/C (1975-76) Part #27-1087 $45.95 Set/2 -
Sale!Shock Absorber Set - (Monza Slimline) Chrome Springs with Chrome shock body. 12 3/4" (324mm) eye to eye. 10.2mm ID top & bottom. Fits: XS1/XS1b/XS2/TX650 (1970-73) Part #06-3614 $79.95/Set/2
-
Sale!XS1/XS1b 1970-71 Shrouded type shock absorber set. Chrome and Yellow XS1b type paint 12.7" eye to eye 10.2mm. mounting eye both ends Fits: 1970-71 XS1/XS1b Part #06-3611 $79.95/Set
-
Out of stockFork Brace - Stiffens front end, improves handling. Precision Steel construction, Chrome plated finish. Fits: 1977-84 650's (over fender). Part #27-1070 $52.95/Ea.
-
Sale!Shock Absorber Set - (Monza Traditional) - Dual Progressive - wound Chrome Springs & Long Black top shroud with black shock body. 11.5" (292mm) eye to eye. Includes preload wrench & set of eye rubbers. Fits: 1974-84 XS/TX650's Part #06-3608 $79.95/Set
-
Sale!Shock Absorber Set - (Monza Sport) - Dual Progressive wound Chrome Springs & Chrome top shroud with Black shock body. 13 3/16" (335mm) eye to eye. Includes preload wrench & set of eye rubbers. Fits: 1974-84 XS/TX650's Part #06-3641 $79.95/Set
-
Out of stockShock Absorber Set - (Monza Standard) - Chrome Springs with chrome shock body no end cap. 12 3/4" (324mm) eye to eye. Includes preload wrench & set of eye rubbers. Fits: 1974-84 XS/TX650's Part #06-3627 $79.95/Set