-
Out of stock
Fork Seal Set - 34 x 46 x 10.5 - Made In Japan by OEM Supplier. Fits: 1970-76 TX/XS 650's (34mm. fork Tubes) Part #27-1016 $8.95/Set -
Out of stock
Fork Seal Washers Pk/2. Fit on top of Fork Seals and below the spring clips in the lower fork legs. Fits: All 1977-84 650's ( 35mm. Forks ) Part #27-1062 $3.69/Pk./2 -
Out of stock
Fork Seal Spring Clips (Pk./2) - These clips fit into the groove above the fork seals in the lower fork legs. Fits: All 1977-84 650's ( 35mm. forks ) Part #27-1063 $3.69/Pk./2 -
Out of stock
Fork Seal Dust Covers (Pk/2) Fits: 1977-84 XS650D-K ( 35mm. fork tubes ) Part #27-1065 $16.95/Pk./2 -
Out of stock
Fork Seal Dust Covers (Pk/2) Fits: 1971-76 XS/TX650's ( 34mm. fork tubes ). Part #27-1066 $16.95/Pk./2 -
Out of stock
Swingarm Pivot Bolt (Shaft) - Bolt with full size thread ( replaces undercut original ). Fits: XS650's 1974-84. Check your original for cracks at the threads. Part #27-1067 $21.95 Ea. -
Bushing (Swingarm Bolt Tube). OEM Ref.# 341-22184-00. Tube is a slip fit through bronze bushings. Replace if original is galled or will not fit through new bronze bushings. Fits: All 650's 1970-84 Part #27-1068 $25.95 Ea. -
Out of stock
Fork Brace - Stiffens front end, improves handling. Precision Steel construction, Chrome plated finish. Fits: 1977-84 650's (over fender). Part #27-1070 $52.95/Ea. -
Swingarm Pivot Bolt (Shaft) - Bolt with full-size thread ( replaces undercut original ). Fits:XS1/XS1b/XS2/TX650 (1970-73 ). Check your original for cracks at the threads. Part #27-1071 $19.95 Ea. -
Sale!
Front Fork Damper Valves (Pk./2) Tuneable Valves are installed on top of the front fork dampening rods and below the fork springs. The adjustable Damper Valve make rod style fork dampers perform like modern cartridge style forks. Fits: 35mm. forks on 1978-84 XS650's. The Best suspension upgrade modification for the XS650 Note: Damper rod drilling required. Photo install instructions included. Part #27-1086 $42.95/Pk./2 -
Sale!
Performance Progressive wound Front Fork Spring Set. Springs Improve handling while retaining OEM geometry. Stops front end droop and diving during braking while improving cornering stability. Progressive design combats bottoming in harsh conditions by increasing resistance as spring compresses. 23mm. Dia. x 495mm. long. 30/40 Lb. /in rate. Fits: 34mm. stock forks on TX650A (1974) and XS650B/C (1975-76) Part #27-1087 $45.95 Set/2 -
Sale!
Performance Progressive wound Front Fork Spring Set. Springs improve handling while retaining OEM geometry. Stops front end droop and diving during braking while improving cornering stability. Progressive design combats bottoming in harsh conditions by increasing resistance as spring compresses. 24mm. Dia. x 484mm. long. 25/35 Lb./in rate Fits: 35mm. stock forks on XS650 (1977-84) Part #27-1088 $45.95/Set/2 -
Fork Gaitors (Set/2) for 1970 XS1 650 but adaptable to All 1971-84 models. (Remove stock dust covers). Give your 650 that "British" look. Provides great fork protection. 1970 models had a lip piece on the lower triple tree on whicht o clamp the boot, for later models simply insert a piece of split rubber rad hose inside and clamp the upper part of the boot to the fork tube. We suggest a breathing hole be punched on a lower pleat also (face to rear) to allow venting of air. Part #27-1089 $22.95/Set/2 -
Out of stock
Cap (Fork Tube Top Cap/Rubber Plug) - Pk/2 - Original type as used on 1977-84 XS650's. Part #27-1091 $5.50/Pk./2 -
Out of stock
Cap (Fork Tube Top Cap/Rubber Plug) - Pk/2 - Original type as used on 1974-76 TX/XS650's + 27-4003 Part #27-1092 $4.20 Pk.2 -
Fork Tube Caps - Set/2 - Stock Chromed Steel OEM type Caps. OEM Ref# 256-23111-60-00 Fit: 34mm fork tubes on - XS1/XS1b/XS2 (1970-72) Caution! Fine thread, use care when installing. Part #27-4000 $29.95/Set/2