| Clutch Holder Tool - Holds Inner and Outer Clutch Hubs So That the Center Nut May be Removed Without Damaging Hubs. Fits: All 650 clutches (1970-84). Part #35-5021 $7.95 ea. |
-
-
Tire Lever - 16" Long Dunlop Type - For those tough tires needing lots of leverage to remove. You need 2-3 of these to do the job! Part #35-0080 $6.95 Ea. -
Cable Luber - Yamaha Pressure Type (Sold Each) Water & dirt are blown down cable by lubricant when pressure spray can nozzle is applied. Spray lube sold by most bike shops. Part #35-0108 $6.95 Ea. -
Sale!
Slide Hammer with Correct Bolt Thread to Remove Engine Rocker Arm Shafts from Head Cover. Works on All 1970-84 650's. Part #35-0121 $10.95 Set -
Precision Carb Sync Gauges Dual Carb Sync Gauge Set with Built in Adjustable Pulse Dampers Mounted on Bracket and with Hoses. Precision Diaphragm type gauge set originally designed for Professional Motorcycle shop use in Japan. Note: Sync gauges hoses hook up to carb holder vacuum air barbs (not included). Your bike must have these air barbs in order to use this sync tool. Part #35-1388 $49.95/Set -
Right Angled Snap ring Plier Set - Reaches in deep to remove clips when rebuilding master cylinders. $9.75 Ea. -
Feeler Guage Set - Metric/Inch Feeler Gauge Set for Setting Valve and Contact Point Clearances. 32pc. Set (Marked in Metric and Inch Sizes). 0.03mm. - (.001") 0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025") 0.07mm. - (.0028") 0.08mm. - (.003") 0.09mm. - (.0035") 0.10mm. - (.004") 0.13mm. - (.005") 0.15mm. - (.006") 0.18mm. - (.007") 0.20mm. - (.008") 0.23mm. - (.009") 0.25mm. - (.010") 0.28mm. - (.011") 0.30mm. - (.012") 0.33mm. - (.013") 0.35mm. - (.014") 0.38mm. - (.015") 0.40mm. - (.016") 0.45mm. - (.018") 0.50mm. - (0.20") 0.55mm. - (.022") 0.60mm. - (0.24") 0.63mm. - (.025") 0.65mm. - (0.26") 0.70mm. - (0.28") 0.75mm. - (0.30") 0.80mm. - (0.32") 0.85mm. - (0.34") 0.90mm. - (0.36") 1.00mm. - (0.40") Part #35-1769 $12.95 ea. -
Sale!
Chain Puller Tool, Pulls new rear-drive chain ends together so that the joiner link can be slipped in place. Ideal for new chains that are difficult to get together for the first time. Part #35-0130 $9.95 ea. -
Sale!
Valve Spring Compressor - Large Honda Heavy Duty Type. This style valve spring Compressor works best on the XS650. Part #35-0122 $39.95 ea.
-
Damper Bolt Driver 8mm Hex - Deep type damper bolt driver used to air impact recessed damper bolts from lower fork legs. 8mm. x 92 Fits: Stock forks 1973-84 Part #35-5022 $5.95 Ea. -
Cam Chain Tool Kit in Case - A "Must Have" Tool to Break and Rivet Cam Chains. Note: Do Not Use for Rear Drive Chains Part #35-0112 $49.95 Set
-
27mm. Box Wrench to fit XS650 Oil Drain Plugs. Long (15") Type for Leverage to Loosen Those Tight Oil Plugs. Part #35-1083 $10.60 ea.
-
Out of stock
17mm. Hex (Allen) Bit Tool to Remove Fork Tube Top Caps. A perfect fit to remove those soft alloy fork tube caps without damage. Fits: Fork caps on TX650A (1974), XS650BC (75-76) and 1977D (version without preload adjuster). Part #35-1081 $6.25 Ea. -
Professional Adjustable Vise Grip Style Clutch Basket and Sprocket Holder Tool. Part #35-9052 $14.95 Ea.
-
Out of stock
Timing Light Inductive Xenon Timing Light. Operates from bikes 12 Volt battery power. The only accurate way to set your 650’s timing and check the advance function. Part # 35-9000 $22.95 Ea -
Fork Oil Level Gauge for Adjusting the Oil Level on all XS650 Forks. Adjustable ring measures oil levels from 0-300mm. in 50mm. increments. 60ml. capacity syringe adjusts fluid levels. Part #35-1084 $11.95/Set
-
Drive Chain Riveter Tool - Rivets high strength rear drive chain Rivet links with hollow pin ends as on our IZUMI 530HT Chain (Rivet link #56-0235) and many DID brand chains. Part #35-0006 $34.95 Ea. -
Terminal Crimper Tool Metric Terminal Crimper Tool, Fastens Metric Terminals to Wires. Professionally Crimps Like Factory Originals. Part #35-0011 $29.95 Ea. -
Chain Press Tool. Used to press on side plates (rivet or clip type) onto rear drive chains. Most late-type High strength drive chains now use a press on side plate on the connecting link (including IZUMI 530 HT). Part #35-0081 $4.95 Ea.
-
Bore Scope 45 degree adaptor. Part # 35-9098 $9.95 Ea. -
Sale!
Bore Scope Professional fibre optic Image Scope for inspecting internal engine parts. 18” long wand with a 1/4” OD tip. Image resolution is 7,400 pixels. Comes in a case with an extra Xenon bulb. Order a 45 degree adaptor (# 35-9098 ) if required. Part # 35-9096 -
Sale!
Long Hex Bit Set Long Metric Hex Bit Set - 8 Pc. long allen type hex bit set. Hard to find 140mm. (5 1/2”) long deep bits for reaching into deep recessed spots. 1/2” drive set in 5,6,7,8,10,12,14 and 17mm. Sizes. Part # 35-9049 $ 29.95 Set -
Out of stock
Alternator Rotor Puller - Safely Pulls Rotor Without Damaging it. Fits: All 650's. Part #35-0040 $9.10 Ea. -
Out of stock
Ring Wrench Ring Wrench to Tighten Muffler Joint Nut on Early XS1 Type Muffler Part #35-5029 $2.95 Ea. -
Out of stock
Ring Wrench to Tighten Steering Head Cogged Nuts. Also fits preload adjuster on some stock Yamaha Shocks. Fits: 60 and 65mm. Part #35-3005 $9.50 Ea. -
Out of stock
Ring Wrench to Adjust Shock Preload. Fits: Our 06-3601/06-3607/06-3608/06-3621/06-3627/06-3641 & 06-3647 shock sets and many other aftermarket shocks. Part #35-5033 $2.90 Ea. -
Out of stock
Circular Spark Plug Gap Tool. Marked in thousandths of an inch and millimeters. Part #35-0136 $1.95 ea. -
Out of stock
Tool for Installing and Removing Spoke or Mag Type Wheel Weights. Part #35-9059 $8.40 Ea.
-
Out of stock
Spoke Wrench Set - A Must Have for Lacing, Truing & Tightening Spokes. 2 Pc. Set. Fits: #8, 9, 10 & 11 Nipple Sizes. Part #35-0109 $4.20/Set/2
-
Out of stock
Replacement Breaker Pin for Cam Chain Breaker Tool. Part #35-0117 $5.50 Set -
Out of stock
Valve Lapping Sticks - Part #35-0059 $6.25Set/2. -
Out of stock
Valve Guide Install / Remove Driver Tool for 1970-84 650's. Part #35-0077 $5.60 Set
