| Circular Spark Plug Gap Tool. Marked in thousandths of an inch and millimeters. Part #35-0136 $1.95 ea. | |||||||
-
Out of stock
-
Out of stock
Ring Wrench to Adjust Shock Preload. Fits: Our 06-3601/06-3607/06-3608/06-3621/06-3627/06-3641 & 06-3647 shock sets and many other aftermarket shocks. Part #35-5033 $2.90 Ea. -
Out of stock
Ring Wrench Ring Wrench to Tighten Muffler Joint Nut on Early XS1 Type Muffler Part #35-5029 $2.95 Ea. -
Out of stock
Spoke Wrench Set - A Must Have for Lacing, Truing & Tightening Spokes. 2 Pc. Set. Fits: #8, 9, 10 & 11 Nipple Sizes. Part #35-0109 $4.20/Set/2 -
Chain Press Tool. Used to press on side plates (rivet or clip type) onto rear drive chains. Most late-type High strength drive chains now use a press on side plate on the connecting link (including IZUMI 530 HT). Part #35-0081 $4.95 Ea.
-
Out of stock
Replacement Breaker Pin for Cam Chain Breaker Tool. Part #35-0117 $5.50 Set -
Out of stock
Drive Chain Rivet Tool Replacement Rivet Pin. Fits: Drive Chain Riveter Tool #35-0006 Part #35-0007 $5.55 Ea. -
Out of stock
Valve Guide Install / Remove Driver Tool for 1970-84 650's. Part #35-0077 $5.60 Set -
Damper Bolt Driver 8mm Hex - Deep type damper bolt driver used to air impact recessed damper bolts from lower fork legs. 8mm. x 92 Fits: Stock forks 1973-84 Part #35-5022 $5.95 Ea. -
Out of stock
Valve Lapping Sticks - Part #35-0059 $6.25Set/2. -
Out of stock
17mm. Hex (Allen) Bit Tool to Remove Fork Tube Top Caps. A perfect fit to remove those soft alloy fork tube caps without damage. Fits: Fork caps on TX650A (1974), XS650BC (75-76) and 1977D (version without preload adjuster). Part #35-1081 $6.25 Ea. -
Cable Luber - Yamaha Pressure Type (Sold Each) Water & dirt are blown down cable by lubricant when pressure spray can nozzle is applied. Spray lube sold by most bike shops. Part #35-0108 $6.95 Ea. -
Tire Lever - 16" Long Dunlop Type - For those tough tires needing lots of leverage to remove. You need 2-3 of these to do the job! Part #35-0080 $6.95 Ea. -
Out of stock
1/2" Drive 27mm. 6 Point Deep Socket. Fits: Clutch Hub Nut on All 650's 1970-84. Part #35-1078 $7.50 ea. -
Out of stock
Tool for Installing and Removing Spoke or Mag Type Wheel Weights. Part #35-9059 $8.40 Ea.
-
Clutch Holder Tool - Holds Inner and Outer Clutch Hubs So That the Center Nut May be Removed Without Damaging Hubs. Fits: All 650 clutches (1970-84). Part #35-5021 $7.95 ea. -
Out of stock
PMA Flywheel Puller - M27 x 1.0 LH outside threaded puller for internal thread flywheel. Part # 35-0041 $9.10 Ea. -
Out of stock
Alternator Rotor Puller - Safely Pulls Rotor Without Damaging it. Fits: All 650's. Part #35-0040 $9.10 Ea. -
Out of stock
Ring Wrench to Tighten Steering Head Cogged Nuts. Also fits preload adjuster on some stock Yamaha Shocks. Fits: 60 and 65mm. Part #35-3005 $9.50 Ea. -
Right Angled Snap ring Plier Set - Reaches in deep to remove clips when rebuilding master cylinders. $9.75 Ea. -
Sale!
Chain Puller Tool, Pulls new rear-drive chain ends together so that the joiner link can be slipped in place. Ideal for new chains that are difficult to get together for the first time. Part #35-0130 $9.95 ea. -
27mm. Box Wrench to fit XS650 Oil Drain Plugs. Long (15") Type for Leverage to Loosen Those Tight Oil Plugs. Part #35-1083 $10.60 ea.
-
Sale!
Slide Hammer with Correct Bolt Thread to Remove Engine Rocker Arm Shafts from Head Cover. Works on All 1970-84 650's. Part #35-0121 $10.95 Set -
Bore Scope 45 degree adaptor. Part # 35-9098 $9.95 Ea. -
Fork Oil Level Gauge for Adjusting the Oil Level on all XS650 Forks. Adjustable ring measures oil levels from 0-300mm. in 50mm. increments. 60ml. capacity syringe adjusts fluid levels. Part #35-1084 $11.95/Set
-
Feeler Guage Set - Metric/Inch Feeler Gauge Set for Setting Valve and Contact Point Clearances. 32pc. Set (Marked in Metric and Inch Sizes). 0.03mm. - (.001") 0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025") 0.07mm. - (.0028") 0.08mm. - (.003") 0.09mm. - (.0035") 0.10mm. - (.004") 0.13mm. - (.005") 0.15mm. - (.006") 0.18mm. - (.007") 0.20mm. - (.008") 0.23mm. - (.009") 0.25mm. - (.010") 0.28mm. - (.011") 0.30mm. - (.012") 0.33mm. - (.013") 0.35mm. - (.014") 0.38mm. - (.015") 0.40mm. - (.016") 0.45mm. - (.018") 0.50mm. - (0.20") 0.55mm. - (.022") 0.60mm. - (0.24") 0.63mm. - (.025") 0.65mm. - (0.26") 0.70mm. - (0.28") 0.75mm. - (0.30") 0.80mm. - (0.32") 0.85mm. - (0.34") 0.90mm. - (0.36") 1.00mm. - (0.40") Part #35-1769 $12.95 ea. -
Professional Adjustable Vise Grip Style Clutch Basket and Sprocket Holder Tool. Part #35-9052 $14.95 Ea.
-
Out of stock
Piston Ring compressor Set Fits 75mm. thru 80mm. piston rings. Part #35-1087 $14.95 ea. -
Drive Chain Breaker Tool, Breaks 520/530 and 630 Pitch Chain. Part #35-0083 $16.50 Ea.
-
Sale!
Long Hex Bit Set Long Metric Hex Bit Set - 8 Pc. long allen type hex bit set. Hard to find 140mm. (5 1/2”) long deep bits for reaching into deep recessed spots. 1/2” drive set in 5,6,7,8,10,12,14 and 17mm. Sizes. Part # 35-9049 $ 29.95 Set -
Out of stock
Timing Light Inductive Xenon Timing Light. Operates from bikes 12 Volt battery power. The only accurate way to set your 650’s timing and check the advance function. Part # 35-9000 $22.95 Ea -
Out of stock
Piston Pin Puller with Adaptors (12.5, 15.75, 19, 22mm. OD). Easily Removes XS650 Piston Pins (20 & 22mm. OD) Without Damage Part #35-9070 $24.90 ea.
