| Clutch Holder Tool - Holds Inner and Outer Clutch Hubs So That the Center Nut May be Removed Without Damaging Hubs. Fits: All 650 clutches (1970-84). Part #35-5021 $7.95 ea. |
-
-
Cable Luber - Yamaha Pressure Type (Sold Each) Water & dirt are blown down cable by lubricant when pressure spray can nozzle is applied. Spray lube sold by most bike shops. Part #35-0108 $6.95 Ea. -
Tire Lever - 16" Long Dunlop Type - For those tough tires needing lots of leverage to remove. You need 2-3 of these to do the job! Part #35-0080 $6.95 Ea. -
Sale!
Slide Hammer with Correct Bolt Thread to Remove Engine Rocker Arm Shafts from Head Cover. Works on All 1970-84 650's. Part #35-0121 $10.95 Set -
Precision Carb Sync Gauges Dual Carb Sync Gauge Set with Built in Adjustable Pulse Dampers Mounted on Bracket and with Hoses. Precision Diaphragm type gauge set originally designed for Professional Motorcycle shop use in Japan. Note: Sync gauges hoses hook up to carb holder vacuum air barbs (not included). Your bike must have these air barbs in order to use this sync tool. Part #35-1388 $49.95/Set -
Right Angled Snap ring Plier Set - Reaches in deep to remove clips when rebuilding master cylinders. $9.75 Ea. -
Feeler Guage Set - Metric/Inch Feeler Gauge Set for Setting Valve and Contact Point Clearances. 32pc. Set (Marked in Metric and Inch Sizes). 0.03mm. - (.001") 0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025") 0.07mm. - (.0028") 0.08mm. - (.003") 0.09mm. - (.0035") 0.10mm. - (.004") 0.13mm. - (.005") 0.15mm. - (.006") 0.18mm. - (.007") 0.20mm. - (.008") 0.23mm. - (.009") 0.25mm. - (.010") 0.28mm. - (.011") 0.30mm. - (.012") 0.33mm. - (.013") 0.35mm. - (.014") 0.38mm. - (.015") 0.40mm. - (.016") 0.45mm. - (.018") 0.50mm. - (0.20") 0.55mm. - (.022") 0.60mm. - (0.24") 0.63mm. - (.025") 0.65mm. - (0.26") 0.70mm. - (0.28") 0.75mm. - (0.30") 0.80mm. - (0.32") 0.85mm. - (0.34") 0.90mm. - (0.36") 1.00mm. - (0.40") Part #35-1769 $12.95 ea. -
Sale!
Valve Spring Compressor - Large Honda Heavy Duty Type. This style valve spring Compressor works best on the XS650. Part #35-0122 $39.95 ea.
-
Cam Chain Tool Kit in Case - A "Must Have" Tool to Break and Rivet Cam Chains. Note: Do Not Use for Rear Drive Chains Part #35-0112 $49.95 Set
-
27mm. Box Wrench to fit XS650 Oil Drain Plugs. Long (15") Type for Leverage to Loosen Those Tight Oil Plugs. Part #35-1083 $10.60 ea.
-
Sale!
Chain Puller Tool, Pulls new rear-drive chain ends together so that the joiner link can be slipped in place. Ideal for new chains that are difficult to get together for the first time. Part #35-0130 $9.95 ea. -
Out of stock
17mm. Hex (Allen) Bit Tool to Remove Fork Tube Top Caps. A perfect fit to remove those soft alloy fork tube caps without damage. Fits: Fork caps on TX650A (1974), XS650BC (75-76) and 1977D (version without preload adjuster). Part #35-1081 $6.25 Ea. -
Damper Bolt Driver 8mm Hex - Deep type damper bolt driver used to air impact recessed damper bolts from lower fork legs. 8mm. x 92 Fits: Stock forks 1973-84 Part #35-5022 $5.95 Ea. -
Professional Adjustable Vise Grip Style Clutch Basket and Sprocket Holder Tool. Part #35-9052 $14.95 Ea.
-
Out of stock
Timing Light Inductive Xenon Timing Light. Operates from bikes 12 Volt battery power. The only accurate way to set your 650’s timing and check the advance function. Part # 35-9000 $22.95 Ea -
Fork Oil Level Gauge for Adjusting the Oil Level on all XS650 Forks. Adjustable ring measures oil levels from 0-300mm. in 50mm. increments. 60ml. capacity syringe adjusts fluid levels. Part #35-1084 $11.95/Set
