- You cannot add "XS1 Overhaul Gasket Set" to the cart because the product is out of stock.
-
Brass Cylinder Head Washer - Can replace all cylinder head sealing washers or all Head Nut Washers used on any 650. 22mm. OD x 10.5mm. ID x 4mm. Thick. Part #01-0651 $9.10/pk./4 Note: The Stock Cylinder Head Sealing Washer ( #01-0650 ) has been discontinued as this brass type has never been seen to leak and last indefinitely.
-
Out of stock10pc. Engine Oil Seal kit - Superior Quality by original Japanese maker (Ars) Includes 2pc. of special triple lip 7mm. thick cam seals. Seals included in kit - Electric start to crank case seal, starter motor shaft seal, kick start seal, shift shaft seal, clutch push rod seal, transmission countershaft seal, upgraded cam shaft seals x2, Crank seal (alternator side) & tach drive seal. Fits: All 650's 1970-84. Part #01-9010 $34.95/Kit
-
Out of stockClutch Pushrod Oil Seal - Made in Japan by Original Maker. OEM Ref.# 93102-08094/08118 ( SD - 8-25-6 ) Ars. Fits: 1970-84 650's Note: The Clutch pushrod seal is a chronic leaker. This seal was made to be replaced when the engine cases are split! It can be replaced without splitting the cases but it is tricky to drive it in intact. We suggest riders purchase more than one as you will need another again someday if not right away if you do not succeed in replacing the seal intact. We suggest you also clean and polish your clutch pushrod as grit & nicks on the rod will saw away at the seal lip causing early wear. Part #01-9019 $4.85 Pc.
-
Out of stock
Engine Kickstart Shaft Oil Seal. OEM.#93102-25064. Ars SD 25-35-7-2HS. Fits: All 650's 1970-84. Part #01-9024 $6.90 Ea. -
Out of stockStarter motor Housing O-Rings ( Pk./2 ) - Square profile Oem Ref.# 306-81827-10-00 Fits: All 650' Starters (1972-84). Part #01-9028 $4.90/Pk./2
-
Out of stock
Gasket Cement - 3-Bond #4 (Yamabond #4) - 100gram tube - Gray semi-drying type. Use on gaskets except head gasket and on all surfaces without gaskets. Part #05-0001 $10.95 /Tube -
Overhaul Gasket Kit for XS/TX 650's 1972-84 650cc. ( 75mm.) Contains: 18-0672 x 1, 18-0673 x 3, 18-0675 (1pr.),18-0852 x1, 18-0855 x 1, 18-0856 x1, 18-0857 x 1, 18-0858 x1, 18-0860 x1, 18-0862 x1, 18-0863 x2, 18-0864 x1, 18-0865 (1pr.), 18-0869 x1, Valve Stem Seals 01-0115 x 4, and (18-0851 Base Gasket Do not use gasket cement on this special Gasket). Note: Gasket Sets do NOT contain copper washers, engine oil seals, cylinder head sealing washers, tach drive or cam chain tensioner o-rings/gaskets. ( These are available separate - See listings below ). Part #18-0208 $49.95/Set
-
Out of stockOverhaul Gasket Set for Yamaha XS1/XS1b ( 70-71 ) 650cc. ( 75mm.) Contains: 18-0672 x 1, 18-0673 x 3, 18-0675 (1pr.),18-0676 x1, 18-0855 x 1, 18-0856 x1, 18-0857 x 1, 18-0858 x1, 18-0860 x1, 18-0862 x1, 18-0863 x2, 18-0864 x1, 18-0865 (1pr.), 18-0674 x1, Valve Stem Seals 01-0115 x 4 and (18-0851 Base Gasket. Note: Gasket Sets do NOT contain copper washers, engine oil seals, cylinder head sealing washers, tach drive or cam chain tensioner o-rings/gaskets (These are available separate - See listings below). Part #18-0652 $59.95/Set
-
Out of stock
Gasket - Cylinder Head - (77.5mm), OEM# 256-11181-01. Fits: XS1/XS1B 1970-71 Only! Part #18-0676 $24.95 -
Out of stock
Base Gasket for Big Bore 750cc Cylinders (85mm. OD sleeve size). Stock type stud holes (dowel pins are used). Fits: Our #05-0750 Big Bore Kit. Part#18-0749 $10.95 -
Out of stock
Big Bore Cylinder Head Gasket (750cc. - 82mm.). Fits: Our XS Performance #05-0750 Big Bore Kits for 1974-84 447 type engines. Part# 18-0750 $32.95 -
Out of stockOverhaul Gasket Kit for XS/TX 650's 1972-84 650cc. ( 75mm.) Contains: 18-0672 x 1, 18-0673 x 3, 18-0675 (1pr.),18-0750 x1, 18-0855 x 1, 18-0856 x1, 18-0857 x 1, 18-0858 x1, 18-0860 x1, 18-0862 x1, 18-0863 x2, 18-0864 x1, 18-0865 (1pr.), 18-0869 x1, Valve Stem Seals 01-0115 x 4, and 1 - 18-0851 Base Gasket Note: Gasket Sets do NOT contain copper washers, engine oil seals, cylinder head sealing washers, tach drive or cam chain tensioner o-rings/gaskets. ( These are available separate - See listings below ). Part #18-0752 $69.95/Set
-
Sale!
Used stock 650 Cylinder Head - 447 type - Takeoff - sold as is - 45 in stock at this time in 20/20. Decent shape for rebuilding - 72-84 type. No Cam, Cam bearings Tappet Covers or Cam end caps included. Usually has Rocker Arms, Rocker Shafts, Valves and Valve Springs. Components Untested. Number matched top and bottom castings. Part #18-0753 $99.00 -
Top End Engine O-Ring Set - 16pc. Kit Contains - 2pc. Cylinder Sleeve O-ring 1.9 x 81.5 # 93210-82153 + 4 pc. Rocker shaft cap O-ring 2.5 x 17 # 93210-17143 + 4pc. Valve - Guide O-Ring 1.5 x 14.5 # 93210-15151 + 4pc. Cylinder head cover insert O-Ring 1.8 x15 # 93210-12152 + 2 pc. Cylinder end cover housing O-Ring 2.3 x 45 # 93210-45150. Fits: All 1970-84 650's. Part #18-0855 $12.00/Kit
-
Out of stock
Filter Element Cover Gasket - (For filter cover in clutch case). OEM Ref.# 256-15456-00. Fits: All 650's' Also used with XS #15-6504 Performance Oil Filter & cooler kit. Part #18-0856 $3.00 -
Out of stockOil Filter Element Base Gasket. Fits under the clutch case filter element. OEM Ref.# 256-13445-00. Fits: All 650's 1970-84. Also used with XS #15-6504 Performance Oil Filter & cooler kit. Part #18-0857 $1.90
-
Intake Spiggot Gasket (Pk./2) Intake Spiggot Gasket (Carb Holder Rubber) (Pk./2), OEM Ref.# 256-13556-01. Fits: Between XS650 Manifolds (Carb Spacers) and cylinder head and between the XS manifolds and the carb holders for the PWK 32. Fits: 1970-84 650's Keihin Flatslide PWK 32mm XS Performance Carb Set for XS650. And All Stock Carb Holders. Note: 2 sets required. Part #18-0865 $4.90/Pk./2
-
Top End Copper Sealing Washer Kit - 9 pc. Kit Contains: 1pc. # 90430-14043 ( @ Oil feed tube base at crankcase), 4 pc. # 90430-10027 ( @ Oil feed tube - Top of head at bolts), 2 pc. # 90430-11033 (@ Rear of cam chain guide support nuts to cylinder front), 2 pc. # 90430-06014 @ (Cam chain guide fastening bolts at front of cylinder). Fits: All 650's Part #18-0870 $5.50 -
Bottom End Copper Sealing Washer Kit - 13 pc. Kit Contains: 6pc.of # 90430-08143-00 ( @ Crankcase Bottom - Nut washers), 2 pc.of #90430-06014 ( @ Oil filter cover screws in clutch case), 3 pc. 90430-06014 ( @ 3 Clutch case upper front screws), 1 pc. of # 90430-06014 ( @ Tach drive retaining bolt ), 1pc. 37R-82543-00/90430-11034 ( @ Neutral switch base ). Fits: All 650's. Part #18-0871 $6.50/Kit
-
Out of stock
Copper Gasket - Cam Chain Adjuster Screw / Lock Nut. OEM Ref.# 90430-18130. Fits: E Type tensioner as used on XS650 2F,G/SG/H/SH/SJ/SK (1980-84). Part #18-0872 $1.90 -
Sale!Cam Chain Tensioner Rod to Spring Damper. OEM Ref.# 2H0-12232-00. Original part on XS650H/SH/SJ/SK (1981-84) and will replace OEM # 341-12232-02 as used on (1974-80) models. Part #18-0873 $4.95