-
Out of stockPolished Chrome Shock Crown Nut - Short Type. 17mm hex x 10mm 1.25pitch x 16mm Long. Fits: All Footrest mount bars 70-84 + Fender mount thru point on 76-78's. Part #49-0703 $2.25 Ea.
-
Out of stockChrome Shock Crown Nut - Deep Type. 17mm hex x 10mm x 1.25 pitch x 21mm Long. Fits: Shock absorber upper studs on 74-84 650's. Part #49-0715 $2.25 Ea.
-
Out of stock
Ring Wrench to Adjust Shock Preload. Fits: Our 06-3601/06-3607/06-3608/06-3621/06-3627/06-3641 & 06-3647 shock sets and many other aftermarket shocks. Part #35-5033 $2.90 Ea. -
Out of stockFork Seal Spring Clips (Pk./2) - These clips fit into the groove above the fork seals in the lower fork legs. Fits: All 1977-84 650's ( 35mm. forks ) Part #27-1063 $3.69/Pk./2
-
Out of stockFork Seal Washers Pk/2. Fit on top of Fork Seals and below the spring clips in the lower fork legs. Fits: All 1977-84 650's ( 35mm. Forks ) Part #27-1062 $3.69/Pk./2
-
Out of stockCap (Fork Tube Top Cap/Rubber Plug) - Pk/2 - Original type as used on 1974-76 TX/XS650's + 27-4003 Part #27-1092 $4.20 Pk.2
-
Out of stockCap (Fork Tube Top Cap/Rubber Plug) - Pk/2 - Original type as used on 1977-84 XS650's. Part #27-1091 $5.50/Pk./2
-
Out of stockReplacement Shaft Needle Bearing for #28-1011 Conversion Kit. Part #28-1020 $7.95 Ea.
-
Out of stockFork Seal Set - 34 x 46 x 10.5 - Made In Japan by OEM Supplier. Fits: 1970-76 TX/XS 650's (34mm. fork Tubes) Part #27-1016 $8.95/Set
-
Out of stockFork Seal Set - 35 x 48 x 10.5/11 - Made In Japan by OEM supplier. Fits: 1977-84 XS 650's (35mm. Fork Tubes). Part #27-1007 $8.95/Set
-
Out of stockRing Wrench to Tighten Steering Head Cogged Nuts. Also fits preload adjuster on some stock Yamaha Shocks. Fits: 60 and 65mm. Part #35-3005 $9.50 Ea.
-
Replacement Shock Rubbers, Spacers, and Washer Set. For shocks with Eye Type Mounting Points. Fits: Our shock sets #06-3601, 06-3607, 06-3608, 06-3621, 06-3627, 06-3641, 06-3647 and some other brands. Each Set Contains all items shown (in quantities shown). for one shock absorber. Part #06-3734 $9.90/Set as shown ( for one shock )
-
Out of stockSwingarm Grease Seal Set - Holds grease into bushings & shaft area of swing arm. Helps seal out water & dirt. If your bike has originals they should be replaced! (20+ years). Made in Japan. Fits: All 650's 1970-84 Part #28-1025 $11.85/Set/2
-
Out of stockFork Seal Dust Covers (Pk/2) Fits: 1977-84 XS650D-K ( 35mm. fork tubes ) Part #27-1065 $16.95/Pk./2
-
Out of stockFork Seal Dust Covers (Pk/2) Fits: 1971-76 XS/TX650's ( 34mm. fork tubes ). Part #27-1066 $16.95/Pk./2
-
Out of stockSwingarm Pivot Bolt (Shaft) - Bolt with full size thread ( replaces undercut original ). Fits: XS650's 1974-84. Check your original for cracks at the threads. Part #27-1067 $21.95 Ea.
-
Fork Gaitors (Set/2) for 1970 XS1 650 but adaptable to All 1971-84 models. (Remove stock dust covers). Give your 650 that "British" look. Provides great fork protection. 1970 models had a lip piece on the lower triple tree on whicht o clamp the boot, for later models simply insert a piece of split rubber rad hose inside and clamp the upper part of the boot to the fork tube. We suggest a breathing hole be punched on a lower pleat also (face to rear) to allow venting of air. Part #27-1089 $22.95/Set/2